WB27K5038 General Electric Range (Stove, Oven) Timer Repair |
Failure codes, problems, and resolutions for General Electric timer model # WB27K5038 |
![General Electric (GE) ERCs and General Electric (GE) stove clocks and timers]() |
Manufacturer : |
General Electric |
| Part Number : |
WB27K5038 |
| Appliance Type : |
Range (Stove, Oven) |
| Color : |
|
| Description : |
Electronic clock control kit - the manufacturer has replaced part number WB27K5038 replaced with WB27T10324 |
|
Do you have a failed General Electric WB27K5038 timer?
Click here:
We can repair or replace your faulty WB27K5038 timer. |
![Request Appliance Timer Service]() |
Electronic clock control kit - the manufacturer has replaced part number WB27K5038 replaced with WB27T10324 timer Part Number WB27K5038 is used in the following appliances |
Recent Service Requests for General Electric Part Number WB27K5038| City | Model Number | Failure Code | Problem Description | Resolution |
|---|
| Grand Junction, Colorado | JGSP21GER1WH | N/A | Oven will not turn on. | Awaiting receipt of timer | | Freeport, New York | JGSP20GER2BG | None | Purchased a home with this stove which had not been in use for several years and had some water damages due to a leaking roof. Upon first start, an F! code was displayed which I was able to clear. However, the relays were not clicking (no oven or broiler). I took control apart to look for obvious damages (hence the hot glue on the ribbon connector hold down). Upon reinstall the relays worked - at least intermittently. Then, upon our first use of the broiler, upon shut off the display went dead. A week or so later it suddenly came to life again with the same behavior. It appeared that sometimes I could get the oven to work by doing a temperature calibration first. none the less, a week or so later and the control went dead again. No codes were shown after the first F!.
PS Thank you for you phone help with this. | Beyond Repair | | Dulzura, California | Profile | F1 | Control board does not activate oven | Awaiting receipt of timer | | Swansea, Massachusetts | JGSP31GER | F 1 | Timer beeps constantly and displays the dreaded code F 1. | Awaiting receipt of timer | | Roscoe, Illinois | JGSP40AET1AA | N/A | Timer will not regulate oven temperature at the selected setting. | Repaired | | Fairfax, Virginia | | f-1 | oven will not heat up | Replaced with reconditioned timer | | Chicago, Illinois | 911.3672992 | F1 | Alarm continuous | Repaired | | New York, New York | JGSP31GER3WG | F1 | control constant beeping. power turned off then upon returning power does beeping. | Awaiting receipt of timer | | LaOtto, Indiana | 911.3652191 | No code | When "oven" is selected it just blinks. does not light oven | Repaired | | Southaven, Mississippi | JGSP40AES2AG | N/A | Oven does not maintain proper temperature. Oven temp. is lower than setpoint and is irratic. | Awaiting receipt of timer | | New York, New York | JGSP31GER3WG | F1 | control constant beeping. power turned off then upon returning power so does the beep. | Awaiting receipt of timer | | st clair shores, Michigan | jgsp40aeszag | none | off by 250 degrees | Repaired | | San Diego, California | JGSP31GER1WG | none | Set oven for e.g. 400F. Burner lights, but temperature indicator immediately jumps to 290F, and climbs to 400F in less than 1 minute and burner shuts off. Obviously the oven is barely warm. We have replaced the temperature sensor already, and verified room temperature resistance is within spec. | Repaired | | Owasso, Oklahoma | JGSP30GER3BG | None | With oven temp sensor resistance of 1100 ohms display reads ~230 degrees, with oven temp sensor resistance of 1350 ohms display reads ~500 degrees. | Awaiting receipt of timer | | Pomfret Center, Connecticut | JGSP30GET1BB | Oven controls flashi | Oven does not turn on. When bake, broil or clean functions are pressed, the display just quickly flashes off and on.
Also--From what I've found, this range SHOULD have had a wb27k5187 timer installed, but the 5038 is what I pulled out. | Replaced with reconditioned timer | | Phoenix, Arizona | 911.3652191 | None -no code displa | Control went blank. AC power to the control board is present but nothing is visible on the display. | Repaired | | lebanon, Kentucky | 911.3672590 | na | oven will not reach desired temp | Repaired | | Yuma, Arizona | | F1 | THE OVEN IS BEEPING AND THE F1 ERROR CODE IN ON THE DISPLAY. UNPLUGGED THE OVER AND PLUG IT BACK IN AFTER ABOUT 30 SEC THE ERROR CODE COME UP AND THE OVEN BEGINS TO BEEP AGAIN | Awaiting receipt of timer | | glen oaks, New York | 911.3672991 | N/A | We have changed all other parts and the clock/oven control panel (timer) is not allowing the temperature to ascend to the temperature that is being read on sensor. It will show temperature electronically is 350 degrees F for instance yet it never warms up beyond 200 degrees F.
We have deemed the control panel is no longer working properly. thank you,
Mike Mayo
Note: Igniter and sensor probe are new. | Repaired | | Philo, California | JGSP20/21 | F1 | On the timer: Robertshaw ERC-14500-RP
Displays F1 after a minute or more. Keypad is hardwired to electronics. It reacts to each key, whether showing a fault or not. Same behavior after being removed from range and powered via cheater cord. | Replaced with reconditioned timer |
|
Established in
