Many failure codes are caused by a faulty timer (also known as the Electronic Range Control). Sometimes, even when the failure code implies that another component has failed this can actually be a timer problem (whereby the timer is not displaying the correct fault code). If you are not sure whether the code you are seeing is due to a problem with the timer please call us, or send us an email, since we can help you determine whether the failure code is likely a timer problem or a problem with some other component. We can repair most timers so if you are sure your problem pertains to the timer (or ERC) please fill out a repair service request and send us your timer to be repaired.
Glass link Electronic Range Control (ERC)
| Door flashing #0, 1, 2, 3 | Latch switch broken | Replace |
| Lock flashing | Latch switch broken | Replace |
| F0 | Loss of safety signal | Replace adapter board |
| F1 | Watchdog circuit | Rebuild Electronic Range Control (ERC) |
| F2 | Oven too hot | Replace oven temperature sensor |
| F3 F4 | Open or shorted oven temperature sensor | Replace oven temperature sensor |
| F7 | Shorted touch panel | Replace glass panel |
| F9 | Motorized door | Check latch |
| FF | Lock error | Check switch and motor |
Electronic Range Control (ERC) III / Relay board with separate board and push buttons
| F0 | Shorted push pad | Replace |
| F1 | Failed Electronic Range Control (ERC) | Rebuild the controller |
| F2 | Oven too hot | Replace oven temperature sensor |
| F3 F4 | Shorted or open oven temperature sensor | Replace oven temperature sensor |
| F5, F6, F8 | Failed Electronic Range Control (ERC) | Rebuild the Electronic Range Controller |
| F7 | Shorted or sticking button | Check glass alignment, replace touch panel if necessary |
| F9 | Door latch failure | Replace door latch switch or assembly if necessary |
Dual Convection Wall Oven
| F0 | Shorted touch pad | Replace touch pad |
| F1 | Electronic range control failure | Rebuild electronic range control (ERC) |
| F2 | Oven temperature 100 degrees over limit | Replace oven temperature sensor |
| F3 | Shorted oven temperature sensor | Replace oven temperature sensor |
| F4 | Open oven temperature sensor | Replace oven temperature sensor |
| F6 | Electronic range control component failure | Rebuild electronic range control (ERC) |
| F7 | Failure detected in self-clean lock circuitry | Check door latch mechanism |
"Big Oven" 5.1 cubic ft. (Sigma Touchmatic ERC)
| F0-0 | No Error | Initial factory setting |
| F1-1 | Over temperature while cooking | Check oven temperature sensor and wiring first, rebuild control board if oven temperature sensor is good |
| F1-3 | Over temperature while cleaning | Check oven temperature sensor and wiring first, rebuild control board if oven temperature sensor is good |
| F1-5 | Cancel key input out of range | Rebuild control board |
| F1-7 | Keyboard disconnected | Verify wire connection is tight. Rebuild control board if failed |
| F1-8 | Shorted key | Rebuild control board |
| F1-9 | Slave micro not functioning | Rebuild control board |
| F1-A | Circuit board grounding | Rebuild control board |
| F1-C | Control not calibrated | Rebuild control board |
| F1-E | Circuit board data corruption | Rebuild control board |
| F1-F | Circuit board data corruption | Rebuild control board |
| F1-H | Door switch input circuit failure | Check switch and wiring |
| F1-J | Latch switch input circuit failure | Check switch and wiring |
| F3-1 | Oven temperature sensor or oven temperature sensor circuit failure | Check wire connections and oven temperature sensor |
| F9-1 | Auto latch will not lock | Check wiring, motor, and latch switch |
| F9-2 | Auto latch will not unlock | Check wiring, motor, and latch switch |
Established in