| Olympia, Washington | Jenn-Air | Svd48600p | No code - won't heat | Everything works except - the oven (bake or broil). Won't heat. Just stopped working. This happened before and I had to replace the board. When I turn the oven on I hear a click and then a second click, after a few seconds it does this again. Dave 360-480-9471 | Repaired |
| WORCESTER, Massachusetts | Jenn-Air | SVD48600P | N/A | | Repaired |
| Columbus, Ohio | Jenn-Air | SVD48600p | N/A | Quit working when heating element failed... Not a good day. Whirlpool has discontinued the part and I cannot find a new/used one. If you have a new or reconditioned one, I will buy it. Otherwise, I hope you can repair mine.
Thanks | Awaiting receipt of timer |
| Bethesda, Maryland | Jenn-Air | SVD48600P | n/a | 10 days ago, clock display went out and loud buzzing noise came from unit. Flipped breaker and left off for 5 minutes. Turned back on, reset, everything normal. Yesterday, same symptom, but cure doesn't work. Online forums suggest that it is the clock/board, but it is available only as special order (also part no. 71002959). | Awaiting receipt of timer |
| Johnston, Rhode Island | Jenn-Air | SVD48600P | N/A | timer and oven shuts off . nothing shows at all. comes back on but cannot bake above 350 degrees and may shut off. up and down arrows only effect a lowering of temperature. | Awaiting receipt of timer |
| Jefferson, Maine | Jenn-Air | SVD48600P | Just went dead | Was baking potatoes and it just shut everything down mid way through the bake? | Awaiting receipt of timer |
| VANCOUVER, British Columbia | Jenn-Air | SVD48600PC | F3 F5 | Oven stays on for only twenty minutes and then shuts off
error code comes on F3 or F5
can't bake a cake or anything that takes an hour to bake as
the oven shuts off after only twenty minutes | Repaired |
| BROOKFIELD, Wisconsin | Jenn-Air | svd48600p | N/A | bake button and uo arrow do not work | Awaiting receipt of timer |
| Sagle, Idaho | Jenn-Air | SVD48648600P | F2, F5 | Error code comes up when oven is on for more than 45 minutes or temperature is set higher than 450 degrees. | Awaiting receipt of timer |
| Jefferson, Maine | Jenn-Air | SVD48600P | Just went dead | Was baking potatoes and it just shut everything down mid way through the bake? | Awaiting receipt of timer |
| Etobicoke, Ontario | Jenn-Air | Med#92Centre! | N/A | Works fine.. just only providing 120W to the burners. Fans work, lights, everything functions when it's installed, it just doesn't turn on the burners and heat. Just stop working with no signs of trouble. Just this week (Week of Apr 14, 2016). | Repaired |
| Pho. Az, Arizona | Jenn-Air | SVD48600P | Control board fail | The fan of the oven starts out fast and slows down and eventually stops.A technician told us that the control board is causing the problem.It makes the ovens fan start and then stops because the 110 volts arent entering repeatedly.This control board needs to be refurbished. | Awaiting receipt of timer |
| Eau Claire, Wisconsin | Jenn-Air | SVD48600P | none | The timer appears to work fine (has no error codes) but intermittently cannot preheat the oven within the normal timeframe. It can reach 280 degrees but then is extremely slow to increase the temperature by even 5 degrees after that. One time it quickly jumped up to 350 degrees after sitting at 280 degrees for a long time. After the breaker was turned off and back on, it worked one time (pre-heated to 350 degrees in less than 10 minutes), but then stopped working correctly again after that. Now, even turning the breaker off and on does not seem to fix it. | Repaired |
| Kenmore, Washington | Jenn-Air | SVD48600P | Up button does not w | The up button the the control panel doesn't work. This controls the temperature and timer for the stove. | Awaiting receipt of timer |
| Louisville, Kentucky | Jenn-Air | SVD48600P | F-2 and F-3 | Received an F-2 error code after cooking one night. Now when we try to use the bake or broil options, receive error code F-3. | Repaired |
| Batavia, New York | Jenn-Air | svd48600p | n/a | Oven does not heat. Elements test with resistance present in both. It thinks it's functioning. I have another one of these to send you, but that will be a separateinvoice in several months, most likely.
Thanks,
John Stone
3322 W. Main Street Rd.
# 64
Batavia, NY 14020 | Repaired |
| Davidson, North Carolina | Jenn-Air | svd48600P | F2 | I have 2 problems:
Issue 1: During bake, timer/ display goes blank for approx 30-60 seconds and then comes back on, with the clock blinking It is an intermittent problem. It does not appear to be triggered at a specific temperature. The other day it did it 3 times in 10 minutes and then worked fine for the remaining bake time. Problem has been occurring for 6-7 months.
Issue 2: F-2 during bake cycle. This just happened this weekend. It did it 3 times in a row. I would not characterize this new issue as intermittent. | Beyond Repair |
| altamonte springs, Florida | Jenn-Air | | N/A | shutting off and on | Repaired |
| Cheektowaga, New York | Jenn-Air | svd48600p | f1 | f1 code appears followed by a loud beeping after a brief usage | Awaiting receipt of timer |
| Los Angeles, California | Maytag | SVD48600P | no lights on panel | Beeping noise than info panel went out.. no oven, no pilot
Repair guy says needs new.timer but has none | Awaiting receipt of timer |
| Pine Grove, Pennsylvania | Jenn-Air | SVD48600P | F4 | Oven spikes to high temperature and gives the error coder F4 | Timer inspected, no repairs necessary |
| Dollard-des-Ormeaux, Québec | Jenn-Air | SVD48600P | Timer doesn't power | Baked element died along with it the timer stopped working. I replaced the bake timer but oven controls aren't working. | Beyond Repair |
| lindsay, Ontario | Jenn-Air | svd48600p | N/A | everything works except the on off button for the oven, i will mail off the part tomorrow, | Timer inspected, no repairs necessary |
| Baltimore, Maryland | Jenn-Air | SVD48600P | NA | oven only reports a 100degree temperatvre and fails to warm up. Service identified controller as the problem, but noted that they are out of stock. Found this site to repair. Thanks! | Repaired |
| veneta, Oregon | Jenn-Air | svd48600p | none on one/E4 on ot | Older timer failed with E4 code
Newer timer had no code
Both not heating up oven - elements and sensor have been checked/replaced | Beyond Repair |
| Baytown, Texas | Jenn-Air | SVD48600P | N/A | Broiler element turned on by itself and would not cancel.(gibberish on panel) I flipped breaker off, waited about two hours turned back on there was nothing showing on timer and it is inop. | Beyond Repair |
| Scarborough, Ontario | Jenn-Air | SVD48600PC | N/A | Display goes off intermittently whether oven is on or not. Will sometimes come back on if you tap the face of the timer. Also, the broiler and the fan will turn on (sometimes) of its' own accord when the oven is on. At one time we had an F2 error code but it doesn't do that anymore. | Beyond Repair |
| Los Angeles, California | Maytag | SVD48600P | no lights on panel | Beeping noise than info panel went out.. no oven, no pilot
Repair guy says needs new.timer but has none | Awaiting receipt of timer |
| Acton, Massachusetts | Jenn-Air | svd48600p | do not know | Buzzing, oven not working, burners still work if light manually | Repaired |
| Miami, Florida | Jenn-Air | SVD048600P | N/A | OVEN WILL NOT TURN ON, CLOCK WORKS... | Awaiting receipt of timer |
| Braintree, Massachusetts | Jenn-Air | range | N/A | totally not working-need new one | Awaiting receipt of timer |
| Melrose Ma., Massachusetts | Jenn-Air | SVD48600P | Not Shown | Self Cleaning has not worked for along time
Current problem oven and broiler not heating at all
Service Tech from Gray's Appliance Melrose Ma. told me the problem
was the timer. | Repaired |
| Santa Rosa, California | Jenn-Air | svd48600p | N/A | I don't have the timer, and the part is no longer available new. | Awaiting receipt of timer |
| Burlington, Ontario | Jenn-Air | SVD48600PC | N/A | Oven does not reach/hold requested temperature | Repaired |
| Hancock, New Hampshire | Jenn-Air | svd48600p duel fuel | none | The oven took forever to reach its temperature, thermostat was replaced, and then the oven stopped entirely. A service person indicated it was this part that needed to be replaced, but he was unable to find the part through his sources. | Awaiting receipt of timer |
| Smithfield, Utah | Jenn-Air | SVD48600P | NA | Doesn't light up and no response from buttons. | Awaiting receipt of timer |
| Baton Rouge, Louisiana | Jenn-Air | | F-5 | Oven does not heat. Gas cooktop still works | Awaiting receipt of timer |
| Alsea, Oregon | Jenn-Air | Jenn-Air SVD48600P | N/A | Touch pad does not respond. Cannot turn oven on. | Awaiting receipt of timer |
| Salt Lake City, Utah | Jenn-Air | SVD48600P | F3 | Oven begins preheating, but eventually gives an F3 error and shuts off. (Last time this happened was at 375 degrees.) We have replaced the thermo sensor and get same error. Sometimes the F3 alternates with an F5 error.
I would be open to replacing the control panel if you have one available. Thanks, Ryan | Awaiting receipt of timer |
| Hot Springs, Arkansas | Jenn-Air | SVD48600P | N/A | Oven intermittently doesn't go on | Repaired |
| Huntsville, Alabama | Jenn-Air | svd48600p | intermittent power i | intermittent power interrupt | Repaired |
| Columbus, Ohio | Jenn-Air | svd48600p | ----- | Control unit nonresponsive. Will not light up. Range works just fine but there is no ability to use the oven. Fan/lights work when powered but they seem to be independent of the control unit. | Beyond Repair |
| Southgate, Kentucky | Jenn-Air | svd48600p | none | oven will not get up to temp requested . everything else works . appliance repairman told me it needs to be replaced. | Repaired |
| Burlington, Vermont | Jenn-Air | SVD48600P | F2 | The f2 code went off and the upper heating element remained on. The oven heating element would not turn off even though the timer indicated that the move was not on. I turned off the circuit breaker to the range and left it off or a bit. When i turn the breaker on the oven resumed heating even though the timer indicated it was off. | Repaired |
| Brownstown, Michigan | Jenn-Air | SVD48600P | None | Alarm Sounds when not using Drops out of bake cycle Using igniter changes clock | Awaiting receipt of timer |
| Sagle, Idaho | Jenn-Air | SVD48648600P | F2, F5 | I wish to purchase a refurbished timer | Awaiting receipt of timer |
| Cassel, California | Jenn-Air | Jenn Air SVD48600P | N/A | Touchscreen is dark. Oven will not turn on and a humming sound is present.
Stovetop burners work OK. | Repaired |
| Okc, Oklahoma | Jenn-Air | Jenn air svd48600P | Up arrow not working | Up arrow quit working. If cannot repair would love to purchase a reconditioned or new one. You can contact me at 405.341.4771x101 | Awaiting receipt of timer |
| Pickerington, Ohio | Jenn-Air | SVD48600P | F3 | After oven is at entered temperature for a while, error code F3 displays and oven shuts off. Convection fan in oven runs intermittently when not on convection and sometimes when oven is off. | Awaiting receipt of timer |
| Whitefield, New Hampshire | Jenn-Air | SVD48600P | no bake or broil | no bake or broil , checked for power out at board , no power out | Repaired |
| Chicago, Illinois | Jenn-Air | SVD48600P | N/A | Blinks on and off | Repaired |
| Edina, Minnesota | Jenn-Air | SVD48600PU | none - no display | the display doesn't work, so I can't operate the oven, clock, timer, etc. | Beyond Repair |
| Whitby, Ontario | Jenn-Air | SVD48600-60 | N/A | Control panel ceased operation. Audible hum when power connected. Visual inspection of capacitors yielded no clues. Slight discoloration in Upper left corner of display panel. | Repaired |
| Penfield, New York | Jenn-Air | svd48600p | N/A | Digital display is not functioning properly. | Awaiting receipt of timer |
| Atlanta, Georgia | Jenn-Air | SVD48600P | N/A | The Bake or clock does not work any longer. The up button on the temp does not work. It started blinking out prior to those problems. | Repaired |
| lees summit, Missouri | Jenn-Air | svd48600p | N/A | Oven elements notworking | Awaiting receipt of timer |
| Kanata, Ontario | Jenn-Air | SVD48600PC | none | Repairman indicated there was a problem with the bake function. There was no code indicating a problem but the oven would not go beyond 280 degrees regardless of oven setting.
Broiler seemed to function properly. | Repaired |
| Chicago, Illinois | Jenn-Air | SVD48600P | N/A | Blinks on and off | Repaired |
| lees summit, Missouri | Jenn-Air | svd48600p | N/A | Oven elements notworking | Awaiting receipt of timer |
| quincy, Massachusetts | Jenn-Air | SVD48600P | N/A | could you fix the one I have if you do not have one? | Awaiting receipt of timer |
| Anglemont, British Columbia | Jenn-Air | SVD48600PC | N/A | When bake button is pushed if you push the up arrow 350 appears,but as you push the up button the temperature selected goes down just as if you were pushing the down arrow.If you select broil the up arrow increases the temperature as it should. Everything else functions normally. | Repaired |
| Snowflake, Arizona | Jenn-Air | svd48600p | N/A | No display, dual fuel, burners and exhaust fan work but not electric oven. | Awaiting receipt of timer |
| Katy, Texas | Jenn-Air | SVD48600P | N/A | NO DISPLAY NO BEEP NOISE NO START THE OVEN | Awaiting receipt of timer |
| red lion, Pennsylvania | Jenn-Air | SVD48600P | none | up arrow on face does not work | Awaiting receipt of timer |
| Saint Paul, Minnesota | Jenn-Air | | Cancel/Stop not resp | Cancel/Stop not responding | Awaiting receipt of timer |
| Grove City, Pennsylvania | Jenn-Air | SVD48600P | SHUTS OFF | i HAVE REPLACED THE Temp probe. The clock will shut off typically above 350 degrees. It does come back on. | Repaired |
| Fairfax, California | Jenn-Air | SVD 48600P | N/A | Completely dead | Awaiting receipt of timer |
| middleboro, Massachusetts | Jenn-Air | svd48600p | none...screen black | oven timer panel not working at all. blank display and none of the buttons appear to work. | Awaiting receipt of timer |
| Cohasset, Massachusetts | Jenn-Air | SVD48600P | N/A | Originally Up arrow did not work. But when loosening a screw to take it off the board shorted before I turned off the power, | Repaired |
| Richmond Hill, Ontario | Jenn-Air | SVD48600PC | none - oven just tur | When we use the oven, the display starts to blink and the oven turns off. Sometimes the display goes off entirely. Eventually the display returns and the oven functions once again. | Repaired |
| Brazoria, Texas | Jenn-Air | sdv48600p | n/a | Started preheating oven and heard an electrical short type noise. Panel went blank. Can get some lights if you hold down the cancel button or the up down arrows. | Beyond Repair |
| Sneads Ferry, North Carolina | Jenn-Air | SVD48600P | n/a | Oven, broiler, oven cleaning and convection will not get hot-inop. | Repaired |
| Bedford, New Hampshire | Jenn-Air | SVD48600P | no failure codes | "Cooling fan" runs when oven goes above 250 degs (didn't used to do this---functionally everything works but my wife says she cannot live with the noise!
Started happening after one day when controller made some funny relay or sparking noise when a stove top burner was turned on. | Awaiting receipt of timer |
| Sugar hill, Georgia | Jenn-Air | Svd48600p | N/A | No power | Awaiting receipt of timer |
| Ajax, Ontario | Jenn-Air | SVD48600PC | F2 | Won't heat up | Awaiting receipt of timer |
| Ajax, Ontario | Jenn-Air | SVD48600PC | F2 | Won't heat up | Awaiting receipt of timer |
| Portland, Oregon | Jenn-Air | SVD48600P | N/A | The timer buttons do not always function, meaning the timer and oven temperature cannot be set. The problem is worsening, to the point that the buttons almost do not work at all. | Awaiting receipt of timer |
| Miami, Florida | Jenn-Air | SVD048600P | f2, f3,f4 | The oven turns on with breaker at full heat, will not shut off unless breaker is turned off. | Repaired |
| Portland, Oregon | Jenn-Air | SVD48600P | none | LCD is difficult to read, all digits are "ON" making it difficult to read the time, temperature, etc. Happened after a power outage. | Awaiting receipt of timer |
| Mississauga, Ontario | Jenn-Air | SVD48600PC | N/A | There is an up and down arrows which adjusts both timer and oven temp. Up arrow has bit the dust- gets used the most. Problem is not interrmittant | Repaired |
| The Colony, Texas | Jenn-Air | SVD48600P | No code, there is no | No display on time, all buttons unresponsive. | Beyond Repair |
| Harrisburg, Pennsylvania | Jenn-Air | SVD48600P | F7 | display went blank for a few minutes. Now displays F7 code. | Awaiting receipt of timer |
| Delaware, Ontario | Maytag | S VD 48600PC | no code, just shuts | One day the clock/control panel just shut off. At that time, if we waited a while it would come back on flashing. We would reset everything and all would be good for a short period. Then the same thing would happen. Only as time went on, it didn't come back on. Now it just flashes the time and when we try to turn things on, it just shuts off again. So it can't be used at all now. | Repaired |
| Davidson, North Carolina | Jenn-Air | SVD48600P | N/A | Up arrow button to increase oven temperature does not work. | Awaiting receipt of timer |
| Trochu, Alberta | Jenn-Air | SVD48600PC | F3 | Oven heats up to temperature, then in about 10 minutes it gives the F3 Error. The very first time was a F5 Error code, then consistently was F3 after many attempts. Did the usuals, turned off the breaker, restarted, still code F3. Note: we put a brand new sensor in and still get the F3 Error code. | Repaired |
| Fayetteville, Georgia | Jenn-Air | SVD48600P | F3 | Front panel cover has hole and up button might need repair. F3 code following temperature climbing randomly. | Beyond Repair |
| MIDLOTHIAN, Texas | Maytag | SVD48600P | Lack | Cant adjust heat higher than 350. Goes down but not up. Up button doesnt appear to work | Awaiting receipt of timer |
| Kingston, Ontario | Jenn-Air | svd48600pc | Oven not going above | Gas cook top working fine.
Oven works only to 350. Will not heave above that.
Will take a new or reconditioned replacement. Thank you. | Repaired |
| St Helena, California | Jenn-Air | SVD 48600P | none | when you push the button to increase the oven temperature, the temperature goes down. Can't get the temp above 325 degrees which is where it is when you press oven on | Awaiting receipt of timer |
| Mountain Brook, Alabama | Jenn-Air | | N/A | "up" key is inoperative | Awaiting receipt of timer |
| Marshfield, Massachusetts | Jenn-Air | SVD 48600P | N/A | we had a technician come in and look at our oven.
We were told we would need a new clock assembly/oven controller - # 5700M662-60
The Serial #: 13397768uk
Other information written on slip:
Electronic control NLA03112
Kitchen Aid Duel Down Draft KSDg950ESS
Jenn Air Dual fuel Down Draft IDS1750FS | Awaiting receipt of timer |
| Davidson, North Carolina | Jenn-Air | SVD-48600P | N/A | Tabs are broke and buttons don't work | Awaiting receipt of timer |
| Hopkinton, New Hampshire | Jenn-Air | SVD48600P | F-1 | F-1 code will not stop beeping | Awaiting receipt of timer |
| Lac Supérieur, Quebec | Jenn-Air | SVD48600PC | N/A | Oven stop and screen turn off also after 5 min. We reset and still shut off | Awaiting receipt of timer |
Established in
