Hoffman Estates, Illinois | Kenmore | 362.7361193 | NONE | completely dead | Awaiting receipt of timer |
Fallbrook, California | General Electric | JGBP34GEP2AD | none | Oven does not heat to indicated temperature.. | Repaired |
Fallbrook, California | General Electric | Gas oven | none | Wont heat to temp | Repaired |
Elyria | Sears | 362-7351890 | F1 | Price for repiar or | Awaiting receipt of timer |
HURST, Texas | General Electric | JGBP26GEN2AD | NONE | OVEN TEMP SENSING 370 OR MORE DEGREES WHEN OVEN ACTUALLY AT ROOM TEMP. SELECTING "BAKE" THAN CHOOSE A TEMPERATURE CAUSES OVEN TO IGNITE MOMENTARILY, DETECTS OVEN IS AT TEMP, SOUNDS READY CHIME, THEN EXTINGUISHES BURNER. OVEN THERMOMETER HAS NOT MOVED NEEDLE OFF BOTTOM STOP AT THIS TIME. I HAVE TRIED TO CALL YOU TODAY ON YOUR OUTSIDE LINE AS WELL AS YOUR WATTS LINE. EXTENSION 10 WILL NOT ACCEPT A VOICE MESSAGE, GIVES THE CALLER "INVALID MESSAGE" RESPONSE, THEN TRIES TO SEND CALLER BACK TO THE RECEPTIONIST. YOUR PHONE SYSTEM IS ALL FOULED UP!!! | Awaiting receipt of timer |
PINSON, Alabama | General Electric | JGBP35GEP4WG | F1 | F1 ERROR CODE COMES UP QUICKLY, AFTER SETTING OVEN TO A TEMP. TO PREHEAT OVEN LIGHTS AND STARTS TO HEAT UP ,AFTER A PERIOD OF TIME OVEN KICKS OFF AND AFTER A COUPLE OF SECONDS F1 COMES BACK. | Replaced with reconditioned timer |
Mountn Albert, Ontario | Hot Point | | N/A | Oven Model # RGB747GER2WH. Oven does not control to proper temperature.
Sent it to place in Scarborough and they said nothing wrong with it.
Would consider one from inventory if it can't be repaired. Please call. | Repaired |
Loretta, Wisconsin | General Electric | JGBP34GEV1AD | F1 | 1. Timer speaker volume very low.
2. For past year all LEDs would come on after a power failure. (pressing the
"clearOff" button would return stove to normal) (normal is clock flashing)
3. When stove is first plugged in, everything works for a minute or so before F1 code
comes on. After that only the top burners work normally. | Beyond Repair |
Florham Park, New Jersey | General Electric | JGBP35GEP2 | F1 | F1 error code and beep alarm | Awaiting receipt of timer |
Lutherville, Maryland | General Electric | XL44 / JGBP34GEP1WH | F1 | IF YOU PUSH THE BAKE BUTTON AND SET THE TEMP FOR BAKING, THE CONTROL WILL GO TO 100 DEGREES (AS IT IS SUPPOSED TO). IF IT IS CORRECTLY WORKING, THE TEMPERATURE BEGINS TO INCREASE AS THE RANGE HEATS UP. HOWEVER, WHAT HAS BEEN HAPPENING IS AFTER 15-30 SECONDS, THE CONTROL WILL CLEAR AS IF THE BAKE BUTTON WAS NEVER PUSHED. THIS PROCESS HAS TO BE REPEATED OVER AND OVER UNTIL FINALLY THE PROCESS PROPERLY BEGINS OR, AS HAS BEEN HAPPENING MORE OFTEN, THE RANGE NEVER BEGINS TO HEAT. | Awaiting receipt of timer |
clifton, New Jersey | General Electric | jgbp34gep3 | N/A | range oven does not get up to temp. gage reads 400 temp. in oven is at 250.. | Beyond Repair |
clifton, New Jersey | General Electric | jgbp34gep3 | N/A | range oven does not get up to temp. gage reads 400 temp. in oven is at 250.. | Beyond Repair |
Scotia, New York | General Electric | JGBP34GEP1 | F1 | Get F1 code and beeping sound. Was intermittent, but now all the time and timer will not work. | Beyond Repair |
Brookline, Massachusetts | General Electric | JGBP34GEP1AD | F1 | F1 displays and bell rings. Oven and broiler do not work. | Beyond Repair |
HUBER HEIGHTS, Ohio | General Electric | XL44 | N/A | OVEN REACHES TEMP BUT THEN SHUTS DOWN AN DOES NOT MAINTAIN SET TEMPERATURE. ALL OTHER FUNCTIONS WORK. | Repaired |
Hinckley, Ohio | General Electric | JGBP34GEP2AD | No display, tansform | This replacement timer has been working fine since replaced 3 years ago. Overnight it just went dark and no sound or buttons work.
Still have original timer, put it in place and time and range functions work. Not using original Eaton timer because unable to keep correct oven temp, caps leaking, and display is dim. | Repaired |
DeWitt, Michigan | General Electric | JGBP26GEN4AD | N/A | The timer on my unit if fine. It is the remaining part of my control mechanism that is bad. The ECR unit is not sending the proper signal (amouont of voltage) to light the igniter when I go to turn on the oven. The output from the 'broil' and 'bake' leads are not sufficient to light the igniter. Is this something that you can fix as well? Model number and part number listed above are for my GE Gas Range. | Timer inspected, no repairs necessary |
Novi, Michigan | General Electric | jgbp31gep1wh | N/A | Temperature not well regulated. | Repaired |
WHEELING, Illinois | General Electric | JGBP35GEP3WG | F1 | CAN NOT CLEAR THE F-1 ERROR CODE | Awaiting receipt of timer |
Bryn Mawr, Pennsylvania | General Electric | JGBP35GEP2WG | N/A | | Awaiting receipt of timer |
Hudson, Ohio | General Electric | JGBP35GEP2WG | N/A | ERC does not attain set temperature. Off by >100 degrees. | Repaired |
Sudbury, Massachusetts | General Electric | JGBP35WEV2WW | F-1 | | Repaired |
Fort Erie, Yukon | General Electric | JGBP35GEV1WH | None | After power failure - buzzer on timer board just makes a buzzing sound - no display | Awaiting receipt of timer |
Livonia, Michigan | General Electric | JGBP26GEN2AD | F-1 | Set temperature on oven and it won't start up or it starts but it stops and then the failure code appears. This is a gas stove | Beyond Repair |
Fair Lawn, New Jersey | General Electric | jgbp34gev1wh | N/A | increase pad dasn't work | Awaiting receipt of timer |
Owensboro, Kentucky | General Electric | Kenmore | f-1 | no function beeping noise f-1 error code | Awaiting receipt of timer |
eastport, Maine | General Electric | | N/A | oven doesn't light | Awaiting receipt of timer |
WALLINGTON, New Jersey | General Electric | JGBP34GEP2AD | F 1 | F 1 KEEPS COMING UP | Awaiting receipt of timer |
glenshaw, Pennsylvania | General Electric | jgbp34gep1ad | N/A | oven will not come on | Repaired |
Crossville, Tennessee | General Electric | gexl44 0315030 | N/A | oven will not turn on unless you keep clicking it and it will eventually turn on. | Repaired |
Fountain Hills, Arizona | General Electric | GE XL44 | None | Screen Dark. No oven control functions | Repaired |
Suttons Bay, Michigan | General Electric | gexl44 | none | Oven temp much lower than indicated on panel. Oven doesn,t heat to desired temp. broiler works fine. already installed new igniter. checked the oven temp sensor,Reads 1095 ohms at board. | Repaired |
glenshaw, Pennsylvania | General Electric | JGBP34GEP1AD | F1 | AFTER POWER OUTAGE - SHOWS CODE F1 | Awaiting receipt of timer |
Chicago, Illinois | General Electric | 3GBP35GEP3WG | N/A | The oven will not go to the indicated temperature. Other features work OK. | Repaired |
Westampton, New Jersey | General Electric | JGBP35GEP4WG | F1 | F1 fault can not be cleared | Repaired |
shoreline, Washington | General Electric | JGBP34GEP2AD | NONE | WILL NOT REGULATE OVEN TEMP | Repaired |
Westampton, New Jersey | General Electric | JGBP35GEP4WG | F1 | F1 fault can not be cleared | Repaired |
Kankakee, Illinois | General Electric | JGBP35GEP4WG | F1 | The F1 Code was intermittent but on this occasion the oven and the broiler light would not work. They did not make the usually beep. The oven temperature did not light up. | Awaiting receipt of timer |
Titusville, Florida | General Electric | jgbp34gev1ad | f1 | please help | Awaiting receipt of timer |
Rochester Hills, Michigan | General Electric | JGBP35AEV2AA | N/A | Timer display stopped working and then there was a buzzing noise not associated with the timer, obviously, since it was not capable of working. | Awaiting receipt of timer |
Altadena, California | General Electric | JGBP35GEP | N/A | the "up" button is not working, cannot increase temperature, etc. | Repaired |
McKean, Pennsylvania | General Electric | JGBP34GEP5AD | None | Oven temp is way lower than what control is set to. Can not reach temps required to bake. | Awaiting receipt of timer |
shoreline, Washington | General Electric | JGBP34GEP2AD | no code | oven will start to heat then stop at less than 150 even though its set at 350.
broiler work's fine though | Repaired |
Issaquah, Washington | General Electric | JGBP35WEW1WW | N/A | GE answer line said I need new Timer ERC2. Screen is totally dark and oven not working. No circuit breaker problem. Part is discontinued. | Repaired |
east Petersburg, Pennsylvania | General Electric | XL44 | none | actual temp of oven is below the set temp by a varying rate from 0-100 degrees and is not consistently off. | Repaired |
Annandale, Virginia | General Electric | JGBP26GEN4AD | N/A | Need a new or reconditioned timer. | Awaiting receipt of timer |
Soulsbyville, California | General Electric | JGBP34GEP1AD | N/A | Following a sudden power outage, panel indicated a failure code which I can't recall. After fiddling with it, the code went away, but the oven would no longer heat up to desired temperature. Even with the user adjustable setting at +35, the oven still is 25-75 degrees F lower than indicated by timer. | Repaired |
Rockville, Maryland | General Electric | JGBP35GEP3WG | N/A | Oven appears to heat to selected temp but does not hold that heat. Repair guy says oven control board is needed. If you do not have reconditioned part I would consider sending in my defective part. Not sure the part number above is correct. Repair parts websites do not list my exact model number but show JGBP35GEP3 without the WG suffix. Under this model number they show part as PS238431, which is listed as "not available." RepairClinic.com refers user from PS238431 to WB27T10083. | Repaired |
Arlington, Virginia | General Electric | JGBP34GEV1WH | none | will not go higher than 350 degrees | Awaiting receipt of timer |
Livonia, Michigan | General Electric | JGBP31GEP | N/A | BAKE BUTTON NOT WORKING - WHEN IT WORKS IT GETS TO 100 AND SHUTS OFF | Awaiting receipt of timer |
NY, New York | General Electric | jgbp35gep4wg | F1 | non stop beeping | Awaiting receipt of timer |
Myrnam, Alberta | General Electric | JGBP35AEW1AA | none | There is no display on the oven control, and no buttons work at all | Repaired |
Allison park, Pennsylvania | General Electric | JGBP26GEN6AD | N/A | Oven temperature is half of displayed temperature | Awaiting receipt of timer |
Tulsa, Oklahoma | General Electric | JGBP34GEV1WH | None | No failure code. Both oven and broiler will not light. Replaced igniter on oven with no change. No voltage from relay on control board for oven or broiler. Was intermittent but now will not work at all. | Repaired |
Martinsburg, West Virginia | General Electric | JGBP34GEP2AD | F! | Starts but bake or broil goes off. After pushing several times, get F1 code. Turned power off to stove for a minute and get F1 code | Awaiting receipt of timer |
Scarborough, Ontario | General Electric | JGBP35GEP4 | F1 | The timer panel is flashing F1 and would not stop until the stove was unplugged, it resumed when the stove was plugged in again. | Repaired |
Millis, Massachusetts | General Electric | JGBP38GES1BB | N/A - Blank Display | Clock / Timer display is blank. There is no beeping when buttons are pushed.
Other electric parts are working: Top light works, Oven light turns on / off when door is opened / closed, Range top igniters work. | Awaiting receipt of timer |
Auburn, Washington | General Electric | JGBP34GEP3AD | No error code | Oven & Broiler relays will not activate. Was intermittent but now a hard failure. All other functions work (clock, timer,etc.)
Checked both ignitiors & gas safety valve all ok. | Repaired |
Seeley's bay, Ontario | General Electric | JGBP35WEW1WW | N/A | Had a hydro service problem and now the board does not power on. | Awaiting receipt of timer |
Campbellford, Ontario | Hot Point | RGB747GER | ? | Timer temperature does not match oven temperature. | Repaired |
Bronx, New York | General Electric | | N/A | clock will not reset, door message always on. | Awaiting receipt of timer |
Cranbrook, British Columbia | General Electric | JGBP35WEW1WW | None - Blank | There is no power to our current timer. If possible, I'd like to order a reconditioned one rather than waiting to have our sent in and back. | Repaired |
Consul, Saskatchewan | General Electric | GE XL44 | dead | I had a flood in my basement while I was away a long time. humidity in my house was quite high over the summer. My stove igniters and lights work fine, but the control board does not power on at all. I'm looking for repair or replacement of control board. | Repaired |
South Elgin, Illinois | General Electric | jgbp35bew1bb | N/A | will not command igniter and gas valve to turn on. | Awaiting receipt of timer |
Lakemoor, Illinois | General Electric | JGBP35GEP4 | N/A | Timer just shut down | Awaiting receipt of timer |
Farmingdale, New York | General Electric | JGBP35GEP4WG (XL44) | F2 & F3 | Temp sensor replaced. F3 comes up can't program timer. F2 comes up. Timer beeps constantly | Repaired |