Maytag RBD275PDT12 Oven Timer

What is the timer/clock part number for the Maytag RBD275PDT12 Oven?

Timer part number 4452890 for Maytag RBD275PDT12

The RBD275PDT12 Oven uses timer part number 4452890.

Do you have a failed Maytag RBD275PDT12 control panel? Click here:

Request Appliance Timer Service

We can repair or replace your faulty Maytag RBD275PDT12 timer.

RBD275PDT12 are also sometimes referred to using these Alternative Names/Model numbers

Whirlpool RBD275PDT12 Oven

RBD275PDT12 Schematic and Wiring Diagrams

Lower oven/literature Parts diagram
RBD275PDT12 Oven Lower oven/literature Parts diagram
Upper oven Parts diagram
RBD275PDT12 Oven Upper oven Parts diagram
Lower oven door Parts diagram
RBD275PDT12 Oven Lower oven door Parts diagram
Upper oven door Parts diagram
RBD275PDT12 Oven Upper oven door Parts diagram
Internal oven Parts diagram
RBD275PDT12 Oven Internal oven Parts diagram
Control panel Parts diagram
RBD275PDT12 Oven Control panel Parts diagram
Top venting Parts diagram
RBD275PDT12 Oven Top venting Parts diagram

Recent Service Requests

CityManufacturerModel NumberPart NumberFailure CodeProblem DescriptionResolution
Jefferson City, TennesseeWhirlpoolRBD275PDT124452890.or. 8302967N/Apower surge caused diodes and risister to openAwaiting receipt of timer
Mission Viejo, CaliforniaWhirlpoolRBD275PDT124452890noneRandom beeping and timer countdown, very annoying constant beeping at times.Awaiting receipt of timer
Fogelsville, PennsylvaniaWhirlpoolRBD275PDT128302967E1 F2No display no controlTimer inspected, no repairs necessary

Common problems for Maytag RBD275PDT12 Oven Timer

Are you encountering a similar problem as them? Contact us now and we will try to help you fix your RBD275PDT12 timer-related problem.
I have a Whirlpool Akkubake Model RBD275PDB12 double oven in black. LIke so many others, I got the E6 F2 code of death after Mrs. Doc used the cleaning cycle. The panel was blank, the only thing that worked was the oven light. Per directions read earlier in this thread, I disconnected the control panel/control board connector ribbon after tripping the breaker. Powered back up and waited. Finally saw a E1 F2 code, but it too is now gone. Am I correct in that this means I need to replace the control panel and not the control board? Doc PS Woke up this morning and the E6 F2 code was back. Since the ribbon connector is still disconnected, does this mean I need a new conrtol board as well? What codes have others gotten during this test?
I have a Whirlpool double oven (model RBD275PDS14). The control panel goes blank about every 2-3 months, and the oven won't heat. Although, the light inside the oven will still work. When the panel lights up again, it shows an error, "E6 F2". If we just wait around, the oven has started working again in about 1-2 weeks without any loss of time on the clock. We have had the panel replaced once, however the problem has continued. Any suggestions?
Whirlpool oven model RBD275PDT12 display showing error code E6 F2 after display out for 12 hours. My daughter was cooking Friday night. She said she saw the display say ''end''. On saturday morning display was dead. Now Sunday display was reading E6 F2. I just heard some beeps from the oven while writing this up and now the display is dead. The beeps sequence was ''medium long short short short''. I'm not sure but I also may have heard another sequence of ''short short long short short short''
We have a Whirlpool self cleaning double oven Model RBD275PDQ12. The panel went blank after doing a self cleaning cycle. Just beeps ...- - - Then it displayed B6 FP for a few hours, but would not respond. Then went blank again.
I have just replaced the control board on my whirlpool oven RBD275 and now it will not turn off or lower the temp. Other controls are working.
How do I calibrate the temperature on a whirlpool acubake double oven?
My whirlpool model RBD275PDQ12 double oven shows an F2 on the display and/or goes blank. I am unable to use the oven during this time. It eventually comes back with the correct time displayed.