Whirlpool LLR9245BQ1 Direct-Drive Washer Timer

#1 (permalink) Yesterday, 04:16 PM beekins Junior Member Join Date: Apr 2011 Posts: 2 beekins Model Number: LLR8245D Brand: Whirlpool Age: 5 - 10 years There was a spin problem, replaced the coupler and dogs did a test, agitate was good, went into spin cycle and loud hum from motor as overload, unplugged and checked work that was done, looked ok, removed agitator and basket, removed tranny, sprayed WD 40 0n brake shoes and reassembled. Did Test, agitate was good, spin was good until end of cycle, as the basket was slowing down there was a loud clanking noise. With the clock in the off position, I turned the basket by hand, and I head the same metal clank sound 2 x in a complete revolution. When I pull up on the basket there is about a fourth to a half inch play. What could it be?? Related Models Whirlpool LLR8245DQ0 Whirlpool LLR8245DZ0 Whirlpool LLR9245AQ0 Whirlpool LLR9245BQ0 Whirlpool LLR9245BQ1 Whirlpool LLR9245DQ0 Whirlpool LLR9245DZ0 Whirlpool LLT7144AN0 Whirlpool LLT7144AQ0 Whir

Whirlpool washer that has a good direct drive but still won't spin or agitate. Would this possibly be a clutch problem?

There was a spin problem, replaced the coupler and dogs did a test, agitate was good, went into spin cycle and loud hum from motor as overload, unplugged and checked work that was done, looked ok, removed agitator and basket, removed tranny, sprayed WD 40 0n brake shoes and reassembled. Did Test, agitate was good, spin was good until end of cycle, as the basket was slowing down there was a loud clanking noise. With the clock in the off position, I turned the basket by hand, and I head the same metal clank sound 2 x in a complete revolution. When I pull up on the basket there is about a fourth to a half inch play. What could it be??

We're trying to replace the clock, we've removed the knob but, we are unable to remove the dial clock to replace with new part. Can anyone help me? PLEASE this is getting very frustrating

WHat is the capacity of the Whirlpool LLR9245BQ1 top load washer?

Symptoms: - Does not spin up to speed ( only about 60% ). However a light load done first might spin full speed. - Tub seems to drain a bit slower than usual. - After drain out and spin, ( even if you get a full speed spin) there will be about an inch of water left in the tub. Clothes at the top of the tub will be spun dry but the lower garments will be soggy. The clock is new and the cycling seems ok. Symptoms react the same in any wash cycle. Pump is clear of obstructions. No visible evidence of motor coupler degeneration,( Black dust on the floor ). Did notice a 2 inch round moist oil spot on the floor when I moved the machine. What do you think? ... A bad clutch?... Worn out motor?... Worn out gearbox slowing the motor? Any and all input will be greatly appreciated.

Whirlpool washer shuts off during cycle Whirlpool model# LLR9245BQ1 shuts off during wash or rinse cyle. This does not happen every time and may stop in any position during the cycle. Sometimes can move the clock dial a notch and it will restart. Other times it will not sart in any clock dial position. Will usually resart after waiting 10 - 15 muntes and pushing in timing dial knob again.

how old is this washer ? ce2148282m/n llr9245bq1

My adgitator is slipping, I think a gear must be broken. the model # is LLR9245BQ1 the serial #CE0910788. My problem is i can't figure out how to get the adgitaton off....Can you help me?

my problem is my washer will go thru the first cycle and will stop at rinse i thought the clock might be bad and replaced that today i stop at rinse anyone have a clue for tucker

leveling my washer LLR9245Bq1 how do I leveling my washer LLR9245Bq1

Recently, my Whirlpool 8 cycle/2 speed washing machine is leaving me with a gallon or more of water in the bottom, leaving my clothes soaking wet! I noticed it rinses and drains perfectly fine on the 1st rinse/spin cycle, but the final cycle is where it is not completely draining. What is causing this? What part would I need replaced as we would like to fix it ourselves.

this washer just stopped working, i checked for power and there is no power at the clock control? is this possible the problem?

I have a top loader model# XXXXX the agitator is slipping, it wants to work if I put down presure on it. Is it possible for me to dissasemble the agitator to check for worn out parts? I can't find my owners manual to see a schematic.

I have a whirlpool washer model number LLR9245BQ1, It stops between cycles and will not continue unless you manually move the dial to the next cycle. Would this be a clock issue or a different problem

I have an older Whirlpool washer, model #LLR9245BQ1, and it just began making a loud noise when it finishes filling with water, and will not agitate or spin. It does drain, and go through the entire cycle, but no drum or agitator movement and a loud knocking/clicking noise. What could the problem be, and are parts available easily for this model?

I have a whirlpool washing machine model LLR9245BQ1 that is leaking oil onto the floor. If you look at the washing machine where the electric motor is on the left I see some black rubber on the floor then to the right is where the oil is on the floor. Enough oil has come out that it has left a oil trial about 2" wide and about 6" out behind the washer. I know the black rubber is coming from the rubber connector between the motor and the transmission ( replaced this part 2 years ago) When I looked at the transmission the oil was coming down from the left side where the motor hooks into the coupling, into the transmission. My wife says the washer is leaving excess water in the clothes after the spin cycle. RepairClinic.com has transmissions for about $185. 1.) is their a fix without buying trany? 2.)is it a DYI 3.)should I just buy new? 4.) washer came with house how do I tell age to see if better to replace. Thanks

I have an Whirlpool Washer Model LLR9245BQ1. The Clothes Mover Agitator, is not moving when I have a load of clothes in the washer. What could be wrong/broken with it?

I have a whirlpool washer Model LLR9245BQ1 serial # XXXXX and need a part. My washer does not spin it does drain. Can you assist me in finding part. My son is a plumber so that would be no problem

Whirlpool top load washer. Water fills up and starts discharging before it is filled up. Recently moved it and now it seems as though it is stuck on extra small cycle. We did a load in extra small cycle and it works fine---we were hoping it was going to recalibrate--it did not. Please help

My Whirlpool washer model #LLR9245BQ1 (top loading) will not drain and stopped in mid cycle, leaving the clothes sitting in a pool of water within it. I believe the motor may have stopped working properly, but either way is can someone please advise how I am able to drain the water so I could even begin to repair the motor? Thanks in advance!